Aramaya Dön

Bowl fragment

İsim	Bowl fragment
Yazar	Unknown
Basım Tarihi:	1250
Basım Yeri	MÃ¡laga (made) -
Konu	Ceramics
Tür	Diğer
Dil	Belirlenmemiş dil
Dijital	Evet
Yazma	Hayır
Fiziksel Boyutlar	Width: 21.50cm, Height: 19cm, Depth: 1.2cm
Kütüphane:	Victoria and Albert Museum
Demirbaş Numarası	1186-1897
Kayıt Numarası	1186-1897
Lokasyon	Middle East Section
Tarih	1250
Notlar	Fragment of a bowl, made in MÃ¡laga, Spain, 1250-1350, tin-glazed earthenware with lustre decoration
Malzemeler ve teknikler	Tin-glazed earthenware painted with a monochrome silver/copper lustre Tin-Glazed Earthenware Lustre-Painted
Fiziksel açıklama	Rim fragment from a small conical bowl, probably originally with a shallow profile. It is glazed on the exterior with a lead glaze and on the interior with an opaque tin-glaze. It is painted with a monochrome silver/copper lustre on the interior only. Its decoration consists of a geometric interlace pattern at the centre, surrounded by a wide frieze of vegetal scrolls border below the vertical rim. Technical Description The original diameter of this bowl can be extrapolated at 23 cm. It probably came down to quite a small base (of roughly the same size as C.1606-1927 ie approx 7 cm), since the thickness of the body starts to narrow as it approaches the foot. It was therefore not very big bowl originally and probably had quite a shallow profile. The clay is very fine and well-levigated. It is very red in colour. The tin-glaze is thick and white, indicating that a large amount of tin oxide has been used in the glaze mixture. The application of the lustre decoration suggests it has been painted on with a brush. It is a good quality lustre . There is a tripod scar at the bottom pointed corner which also has a bit of glaze stuck to it from the bowl which would have originally been stacked inside this bowl during the firing. It is very smooth on the back indicating that it has been turned with a tool. Long dragging areas in the concentric marks on the back indicate where a bit of clay has been caught in the tool as it was turning, probably on a wheel. There is no decoration on the exterior, which seems to have been glazed with a less expensive lead glaze.

Kaynağa git Victoria and Albert Museum Victoria and Albert Museum - Osmanlıca el yazması arama motoru

Victoria and Albert Museum

Bowl fragment

Yazar Unknown

Basım Tarihi 1250

Basım Yeri MÃ¡laga (made) -

Konu Ceramics

Tür Diğer

Dil Belirlenmemiş dil

Dijital Evet

Yazma Hayır

Fiziksel Boyutlar Width: 21.50cm, Height: 19cm, Depth: 1.2cm

Kütüphane Victoria and Albert Museum

Demirbaş Numarası 1186-1897

Kayıt Numarası 1186-1897

Lokasyon Middle East Section

Tarih 1250

Notlar Fragment of a bowl, made in MÃ¡laga, Spain, 1250-1350, tin-glazed earthenware with lustre decoration

Malzemeler ve teknikler Tin-glazed earthenware painted with a monochrome silver/copper lustre Tin-Glazed Earthenware Lustre-Painted

Fiziksel açıklama Rim fragment from a small conical bowl, probably originally with a shallow profile. It is glazed on the exterior with a lead glaze and on the interior with an opaque tin-glaze. It is painted with a monochrome silver/copper lustre on the interior only. Its decoration consists of a geometric interlace pattern at the centre, surrounded by a wide frieze of vegetal scrolls border below the vertical rim. Technical Description The original diameter of this bowl can be extrapolated at 23 cm. It probably came down to quite a small base (of roughly the same size as C.1606-1927 ie approx 7 cm), since the thickness of the body starts to narrow as it approaches the foot. It was therefore not very big bowl originally and probably had quite a shallow profile. The clay is very fine and well-levigated. It is very red in colour. The tin-glaze is thick and white, indicating that a large amount of tin oxide has been used in the glaze mixture. The application of the lustre decoration suggests it has been painted on with a brush. It is a good quality lustre . There is a tripod scar at the bottom pointed corner which also has a bit of glaze stuck to it from the bowl which would have originally been stacked inside this bowl during the firing. It is very smooth on the back indicating that it has been turned with a tool. Long dragging areas in the concentric marks on the back indicate where a bit of clay has been caught in the tool as it was turning, probably on a wheel. There is no decoration on the exterior, which seems to have been glazed with a less expensive lead glaze.